Bv 300 C-Arm Error Dfi Application Not Started - Servicetechniker Forum
advertisement

BV 300 C-Arm Error DFI Application Not Started

Tags: C-Arm, PHILIPS

(5)
(1)

JB

BV 300 C-Arm Error DFI Application Not Started

July 15, 2015 04:39

BV 300 has error "DFI Application not started, software inconsistant or not loadable". We dont have manuals or software for this system. Can someone contact me that can either load software for me or assist me in doing so. Thanks

Log inor Register

to rate and post a comment

(2)
(2)

john eurith

re: BV 300 C-Arm Error DFI Application Not Started

July 15, 2015 06:29

first enter service mode and see carm ip address and configure laptop to static ip within the BV network scheme and connect to service port using crossover cable and then reboot carm for connection using explorer and connect using the target "carm"Ip address.This will connect you to a working dfi.There are other ways to connect but you probably want to consider calling Philips

1 person liked this
Log inor Register

to rate and post a comment

(25)
(3)
(15)

Ari Lipson

re: BV 300 C-Arm Error DFI Application Not Started

July 15, 2015 06:29

you need to reload software. A headache!
where are you located?

Log inor Register

to rate and post a comment

(23)
(9)

Jerry Beeler

re: re: BV 300 C-Arm Error DFI Application Not Started

July 16, 2015 08:15

I figured that software needs reloading but do not have software and am being told by Philips that the system was end of life in 2010 so they don't have software either.

Log inor Register

to rate and post a comment

(50)
(5)

ricardo Usandivaras

re: re: re: BV 300 C-Arm Error DFI Application Not Started

July 17, 2015 09:52

That is not true, i haved same proble 1 month ago and the sofware is allready to load,if you have the license original of your C arm ,you can do the reloading

Log inor Register

to rate and post a comment

(114)
(14)
(1)

bashir ahmad

re: re: re: re: BV 300 C-Arm Error DFI Application Not Started

January 28, 2016 04:09

Hi dear from where can i check this licence no please.

Log inor Register

to rate and post a comment

(8)

Ed Herry

re:re: re: re: BV 300 C-Arm Error DFI Application Not Started

April 23, 2018 04:08

Hi, can u show me how to reload.

Log inor Register

to rate and post a comment

(5)
(1)

lefort

re: re: BV 300 C-Arm Error DFI Application Not Started

July 24, 2017 10:39

In cameroon

Log inor Register

to rate and post a comment

(50)
(5)

ricardo Usandivaras

re: BV 300 C-Arm Error DFI Application Not Started

July 16, 2015 08:15

You need reload sofware ,for this you need software called X-Scope also need too know the license number for this BV300 and also need license to use X-Scoipe or hardware key.
I assume that you dont have any.

Log inor Register

to rate and post a comment

(43)
(4)

Saqib Mirza

re: BV 300 C-Arm Error DFI Application Not Started

July 16, 2015 08:16

Contact at saqib.mirzapk@gmail.com

Log inor Register

to rate and post a comment

(6)

Scott Fishman

re: BV 300 C-Arm Error DFI Application Not Started

September 30, 2015 11:27

I could use some guidance in the DFI software reload process. I installed XScope, connected, entered fault finding and ran the BIST without issue, but when I attempt to install the DFI software The error I receive indicates "No lower sections for this item" leaving me to believe I need a hardware key; Is the hardware key universal to all units or do you need one that matches your serial number? And where do you locate your Software license key? Your assistance is appreciated. Happy to send a gift card or other fair compensation.

Log inor Register

to rate and post a comment

SERVICE ALL C-arms - SPECIALIZE in OEC 9800 & 9900 | CALL CMS 586-532-1142

National service coverage with a well trained and professional team. Complete Medical Services has over 20 years of experience in this industry specializing in OEC C-arm equipment. LOOKING for a pre-owned C-arm - CALL we always have systems in in-stock

advertisement

 

advertisement

 

advertisement

 

advertisement